Instructions for use

USER GUIDE

1. MAIN CODE – четири цифрен ( 1234 фабричен код ). Задължително се сменя с нов главен код. Служи за
turn on and off the system, and enter and change all codes and functions.

2. INSERTING THE SYSTEM UNDER PROTECTION

Before the system is switched on, all doors and windows must be closed and there should be no doors
movement in guarded areas. At the time of dialing the code, the green LED (Ready) must be lit. If you are
your code has been dialed correctly, the keypad starts counting the exit time and the red LED (Armed) lights up.
NOTE: If you have made an error while entering the code, the keypad sounds a short sound, then
press the (#) button and re-enter your code.

3. DISABLING THE SYSTEM

When entering the front door, the keypad starts to sound with continuous sound, which is a warning that
you must quickly enter your personal code. If the System (yellow LED) remains on after the system is turned off,
check with function (*) (2) or (*) (3).
NOTE: If you have made an error while entering the code, the keypad outputs a prolonged sound,
then press the (#) button and re-enter your code.

4. FUNCTIONS WITH (*)

(*) (1) - Bypass (off) of a security zone.

Example: (*) (1) (05) (06) (#) - zones 5th and 6th are excluded from the guard. The alarm system can be switched on
in the order specified in item 2.
When the alarm system is switched off, the bypass fails.

(*) (2) - Overview of problems.

Press the (*) (2) - The "Trouble" or "System" light will flash
problems will be shown with an indication of the respective zones:
Indicator 1 - required technician: press (1) to determine the specific problem:
–
(1) - Low battery;
–
(2) - Problem in the siren chain;
–
(3) - General system problem;
–
(4) - General system tamper;
–
(5) - Total system monitoring.
Indicator 2 - Lack of mains power;
Indicator 3 - Telephone Line Monitoring Problem;
Indicator 4 - Communication failure;
Indicator light 5 - Zone fault;
Indicator 6 - Tamper Zone;
Indicator light 7 - Low battery of device;
Indicator 8 - Incorrect system clock.
Press the (#) button to finish the check.

(*) (3) - Check the zone in which an alarm event occurred.

Press the (*) (3) - the LED on the working zone blinks
Press the (#) button to finish the check.
The LED will go off when you turn the system on again.

(*) (4) - Bell on the door.

Pressing (*) (4) switches on the door bell, if you repeat the same buttons, the bell is switched off.

(*) (5) - Change of access codes.

- change master code-press buttons (*) (5) (old master code) (40) (new master code) (#)
Example: (*) (5) (1234) (40) (2580) (#);
- change of additional code - (*) (5) (master code) (01 to 32) (four digits for code) (#)
Example: (*) (5) (1234) (01) (9876) (#) or example: (*) (5) (1234) (02) (6789) (#).
- delete additional code - (*) (5) (master code) (01 to 32) (*) (#).
Example: (*) (5) (1234) (02) (*) (#) - second code is deleted.

( * ) ( 6 ) – Сверяване на часовника на системата.

- press buttons (*) (6) (master code) (1) (hour, minute) (month, date, year) (#)

Example: (*) (6) (1234) (1) (12; 05) (03; 29; 06) (#).

(*) (7) - Restoration of a fire zone.

When triggered in a fire zone, it remains open (lit) and needs to be restored to switch on
system. This is done by pressing buttons (*) (7) (1) or (2) - the fire zone is extinguished.

and

5. WATER ASSEMBLY BUTTON - If you press the (P) button and hold it more
for two seconds, the siren will not sound, but the system will send your signal to the monitoring center.